When you plan to update your JR FM Transmitter to the newest high-tech 2.4GHz system, CF9 is your correct choice.
Corona 2.4Ghz JR module replacement system.
The Corona 2.4Ghz system replaces the standard JR module on most JR PPM systems equipped with an FM module.

Compatible with JR radios include: 347,388,783,U8,PCM10,PCM10S,PCM10SX,PCM10IIs,8103,9303,MX-22,MX-24s

Specification For Transmitter Module
Operating Voltage Range : 6.0V-13.0V
Operating Current : 100Ma
Output Power---- 10mW-60mW
Resolution : 10bit

Specification for Receiver
CR8D---- Fast Spread 2.4G Receiver work with Corona RF.Module
Operating Voltage Range --- 4.8V-6V
Operating Current --- 30Ma
Specified Range --- 1.5km
Resolutiong ---10 bit
Latency ---- 22ms
Sensitivity -- -100dbm
Channel --- 2CH , 4CH, 6CH, 8CH

Includes:
1 x JR compatible RF module 2.4G
1 x antenna
1 x 2.4Ghz 8CH Receiver

Specifications:

Type: E-FLY100C
Modulation：FM-PPM
Working Currency：≤250mA
Flying Mode：A/V/H/C
Channels: 6 Channels
Signal Power：≤800mW
Voltage Indicator：LCD
Work Frequency：72M/40M/35M
Working Voltage：12V 5#AAA dry battery or
9.6V Ni-ca Battery Pack

Function of Transmitter:
There are four flying mode pre-installed: A (Common plane), V (V tail), H (Common Helicopter), C (CCPM Helicopter)

A (Common plane)

A：Aeroplane
1 The ranges of CH1,CH2 and CH4 of servos can be adjusted by Tiny mix1
in order to adjust for different aerobatics.
2 The function of CH1,CH2,CH4 small angel and large angle can be changed
by switch 3
3 The mixture function of ch1 and ch6 can be achieved by switch 2.
4 There is a isolated channel for landing gear and that function can be
achieved by switch 1
5 Reverse switch for CH1,CH2,CH3,CH4 and CH6
6 Lock and unlock function. When every data is settled ,the situation can be
saved with lock function and every change will be not accepted.
7 Alarm for low voltage: when voltage of battery is under 8.5V,the red LED
will flash and when under 7.5V,LCD will close.

V (V tail)

V：v tail mode
1 The mixture function of ch1 and ch6 can be achieved by switch 1.
2 The range of servo for CH4 can be changed by tiny mix2
3 The function of CH1,CH2,CH4 small angel and large angle can be changed
by switch 3
4 There are two isolated switch channel CH5 and CH6. And collapsable landing
gear as well as photo-taking can be achieved by switch channel 1 and 2
5 Reverse switch for CH1,CH2,CH3,CH4 and CH6
6 lock and unlock function. When every data is settled ,the situation can be
saved with lock function and every change will be not accepted.
7 Alarm for low voltage: when voltage of battery is under 8.5V,the red LED
will flash and when under 7.5V,LCD will close.

H (Common Helicopter)

H：Helicopter mode
1 PIT and PLT can be adjusted by tiny mix 1 and 2
2 The function of CH1,CH2,CH4 small angel and large angle can be changed
by switch 3
3 There is a switch for the function of Gyro and can be switched between
normal mode and head lock mode by switch 1
4 The switch 2 is settled for 3D diverted flight
5 Reverse switch for CH1,CH2,CH3,CH4 and CH6
6 lock and unlock function. When every data is settled ,the situation can be
saved with lock function and every change will be not accepted.
7 Alarm for low voltage: when voltage of battery is under 8.5V,the red LED
will flash and when under 7.5V,LCD will close.

C (CCPM Helicopter)

C：CCPM helicopter mode
1 The mixture function of CH1,CH2,CH3 and CH6 can by achieved for CCPM
helicopter.PIT and PLT can be adjusted by tiny mix 1 and 2
2 The function of CH1,CH2,CH4 small angel and large angle can be changed
by switch 3
3 There is a switch for the function of Gyro and can be switched between
normal mode and head lock mode by switch 1
4 The switch 2 is settled for 3D diverted flight。
5 Reverse switch for CH1,CH2,CH3,CH4 and CH6
6 Lock and unlock function. When every data is settled ,the situation can be
saved with lock function and every change will be not accepted.
7 Alarm for low voltage: when voltage of battery is under 8.5V,the red LED
will flash and when under 7.5V,LCD will close.

And there is a switch button.Ch1, Ch2, Ch4, Ch6 and the reversed buttons are separate，a switch to change the turning range of servos（100%/70%）for CH1,CH2,CH4。The LCD can indicate voltage of battery, situation of channels, flying mode and time. And LCD has the function of low voltage warning.

A：Antenna
B：LCD
1 to indicate the battery voltage of transmitter
2 to show the situation of channels whether it is reversed
3 to show the flying time
4 to indicate flying mode
C：Tiny Mix 1
1 Under Mode A, it is for CH1,CH2,CH4 and CH6 and that can change the turning range of servos.
2 Under Mode V, it is for CH1 and CH2.
3 Under Mode H, it is for PIT adjustment
4 Under Mode C, it is for PIT adjustment
D：Tiny Mix 2
1 Under Mode A, it is for CH6
2 Under Mode V, it is for CH4
3 Under Mode H, it is for PIT adjustment
4 Under Mode C, it is for PIT adjustment
E：Switch 1
This switch is for Ch5 that can be used for aerial camera, collapsible landing gear and shift between gyro mode and gain, etc.
F：Switch 2
1 Under Mode A, it is for CH6
2 Under Mode V, it is can be used for aerial camera and collapsible landing gear.
3 Under Model H, it is the switch for diverted flight.
4 Under Mode C, it is the switch for diverted flight.
G：Flying Mode Switch
When the lock switch is on ADJUST, transmitter will be indicated as Mode A, and it is can be adjusted to A/V/H/C Flying Mode
H: LED Indicator for Power
I：Red LED Indicator for low Voltage: When battery is under8.5V, the LED will have a flash alarm; the LCD will cut off when voltage is under 7.6V.
Note: When red LED flashes or nothing shows on LCD, pls change the battery in order to avoid flying out of control.
J：Joystick
1 If the transmitter is Model 1,CH1is for aileron and CH3 for throttle.
2 If the transmitter is Model 2,CH1 is for aileron and CH2 for Rudder.
K: Joystick
1 If the transmitter is Model 1,CH2 is for elevator and CH4 for rudder.
2 If the transmitter is Model 2,CH3 is for throttle and CH4 for rudder.
L：Tiny Mix for Channels
1 If the transmitter is Mode 1,it is for CH3
2）If the transmitter is Mode 2,it is for CH1
M: Tiny Mix for Channels
1 If the transmitter is Mode 1,it is for CH1
2 If the transmitter is Mode 2,it is for CH3
N：Tiny mix For Aileron
O：Tiny mix for rudder
P：Flying Ring
Q：Switch for Power.
R：Lock Switch
When the lock switch is on LOCK position, all the other shift is under lock; when the lock switch is on ADJUST position, and all can be adjusted.
S：CH1, CH2, CH3, CH4, CH6 Reversed Switch
For changing the turning of servo, up for reversed and down for normal
REV：Reversed NOR: Normal
T：Steel Handle
U：TX Crystal
V：Battery bay for transmitter
W：Plug for Simulator
X：Rechargeable plug(Note:Only 9.6V Nihe battery pack can be recharged)
Y: Switch 3
The switch to change the turning range of servos（100%/70%）for CH1,CH2,CH4. When it is 0, it means the turning range of servos is 100%. When it is 1, it means the turning range of servos is 70%

How to program the FS 2.4G 6ch USB Programmable RC System for the helicopters used the TX/RX

Connect an USB cable from the transmitter to a computer,then turn on the transmitter:

Open the CD on the computer

Open the directory 'PL-2303 Deiver Installer'

Run the file:

Run the 't6config'

There is a new post 'T6comfig' on the desktop of the computer. Turn on the power of the helicopter. make sure the burshless motor 3 ports is already disconnecting on the helicopter:

Open the computer manager and equipment manager to check the new port 'Prolific USB-to-Serial Comm Port (COM9)',and remember the (COM9):

Run the 'T6config' and A menu is appeared:

Click the button 'Setting':

Select ‘COM9' you remember on the step 9:

Move 2 sticks on the transmitter, and block channels follow moving:

Click a button 'Stick Select',select 'MODEL1':

If your transmitter is mode 2 (mode 1 is right hand throttle, mode 2 is left hand throttle), you can select the 'MODEL2'.Other setting item are same with mode 1:

Click a button 'Type', select 'HELI-120',that is CCPM mode:

Click a button 'Reverse', select 'CH4',make the CH4-RUDDER of the transmitter is reversed:

Click a button 'Swash AFR', make sure they are same as follows

Click a button 'Pitch Curve' to setup 'EP0 %' for a low pitch of the blade on the helicopter

Change the 'EP0 %' until the low pitch is -2 degree (or 0- -3 degree) during the throttle stick of the transmitter put down bottom (mode 1 is right hand throttle, mode 2 is left hand throttle):

Setup 'EP4 %' for a high pitch of the blade on the helicopter

Setup 'EP4 %' for a high pitch of the blade on the helicopter

Change the 'EP4 %' until the high pitch is +10 degree (or 8-11 degree) by a pitch meter during the throttle stick of the transmitter put up top, if the EP4=100% still less than 10 degree, need to change the pitch range by the step 18,to change the CH6=-50 to -60 or more

It is a CCPM transmitter with 6 CH,including the fine tuning of screw–pitch
journey curve,screw –pitch journey, handle, flying rings, voltage display LED, 3D
switch and so on.

It is an outstanding transmitter. It not only can accommodate both helicopters and airplanes but also can work with  all of the Walkera spectrum receivers you may already own. With only one WK-2801, all Walkera helis will be under control

The simplest and most advanced 6-channel system available.

The original was a revelation of affordability, proven performance and programming ease, created to ease the transition from 4-channel sport systems into 6-channel computer systems. Today's system offers the original's appeal, 6EXAS and 6EXH enhancements and the revolutionary, interference-free performance of the 2.4GHz FASST System.

Standard Programming Functions :

* Model Select – six model memory.
* Model Type – select airplane or heli programming in one transmitter.
* Servo Reversing – on all six channels.
* Dual Rate/Exponential – for ailerons, elevator and rudder.
* End Point Adjustment – fine-tunes servo throws on all six channels.
* Digital Trim – stores trim settings for each model for aileron, elevator, rudder and
throttle.
* Fail Safe – a safety throttle setting in case of loss of transmitter signal.
* Battery Fail Safe – moves the throttle to a preset position when the airborne pack
reaches 3.8V.
* Stick Mode – choose from Mode 1 through 4.
* Range Checking – Power Down reduces transmitter output power for up to one minute,
allowing range checking from 50 paces away.
* Changeable Throttle Stick – select ratchet for airplanes or smooth for helis.
* Adjustable Stick Length – choose the length that suits your flying style.

Airplane-Specific Programming Functions:

* Wing Mixing – for flaperon, flap trim, V-tail and elevon.
* Trainer System – with the transmitter as either the master or student system.
Compatible with other Futaba systems.
* Throttle Cut – pre-programmed for safely shutting off the engine.
* Programmable Mixing (1 & 2) – two different mixes allow any two channels to be
combined.

Helicopter-Specific Programming Functions:

* 5-Point Normal and Idle Up Throttle/Pitch Curves.
* Throttle Hold – for autorotation.
* Revo (Revolution Mixing) – mixes rudder and pitch together.
* Gyro Mixing – two gyro gain settings can be programmed and selected during flight.
* Swash to Throttle Mixing – corrects slowing of the engine's speed caused by the
swashplate.
* Swashplate Types – choose from 1S (independent aileron, pitch and elevator servos
linked to the swashplate), 3S (120° CCPM), or 3E (90° CCPM).
* Swash AFR – Adjustable Function Rate, for use with 1S, 3S or 3E swash types.



The heart of the FASST system is the R606FS receiver: there's no other 2.4GHz receiver like it!

Size and weight —
The R606FS measures 1.64 x 1.08 x 0.36 inches and weighs just 7 grams without the case...perfect for park flyers, but powerful enough to easily control giant-scale models too. It's the best of both worlds!

Full-range capability —
The competition's full-range system includes a bigger, two-piece receiver; a smaller park flyer receiver must be purchased separately. The compact R606FS unit offers “all-in-one” convenience!

Antenna stress relief —
Unlike other receivers, the R606FS uses rubber grommets to minimize stress on the antennas. This helps prevent the antenna wire from fraying, and possibly putting your model at risk.

Installation ease —
The single R606FS unit can be installed without making any modifications. The competitor's 2.4GHz system requires that their two receivers be mounted in separate locations.
Number of connections —
The competition's two receivers mean two additional connection points, doubling the potential for a problem.

A computer heli system with more for less!

The 6EXH replaces the 6EXA Super's flap rotary dial with a Throttle Hold switch that's great for performing autorotation maneuvers


After accessing the channel menu with the Select button, modelers simply use the Mode button to scroll through. The Throttle Cut button safely kills the engine after landing


The Data Input Lever makes it easy to set end points and rates for all six channels.

Package

How to program the Unisky 6ch transmitter for the helicopters used the TX/RX

Connect an USB cable from the transmitter to a computer,then turn on the transmitter:

Open the CD on the computer

Open the directory 'PL-2303 Deiver Installer'

Run the file:

Run the 't6config'

There is a new post 'T6comfig' on the desktop of the computer. Turn on the power of the helicopter. make sure the burshless motor 3 ports is already disconnecting on the helicopter:

Open the computer manager and equipment manager to check the new port 'Prolific USB-to-Serial Comm Port (COM9)',and remember the (COM9):

Run the 'T6config' and A menu is appeared:

Click the button 'Setting':

Select ‘COM9' you remember on the step 9:

Move 2 sticks on the transmitter, and block channels follow moving:

Click a button 'Stick Select',select 'MODEL1':

If your transmitter is mode 2 (mode 1 is right hand throttle, mode 2 is left hand throttle), you can select the 'MODEL2'.Other setting item are same with mode 1:

Click a button 'Type', select 'HELI-120',that is CCPM mode:

Click a button 'Reverse', select 'CH4',make the CH4-RUDDER of the transmitter is reversed:

Click a button 'Swash AFR', make sure they are same as follows

Click a button 'Pitch Curve' to setup 'EP0 %' for a low pitch of the blade on the helicopter

Change the 'EP0 %' until the low pitch is -2 degree (or 0- -3 degree) during the throttle stick of the transmitter put down bottom (mode 1 is right hand throttle, mode 2 is left hand throttle):

Setup 'EP4 %' for a high pitch of the blade on the helicopter

Setup 'EP4 %' for a high pitch of the blade on the helicopter

Change the 'EP4 %' until the high pitch is +10 degree (or 8-11 degree) by a pitch meter during the throttle stick of the transmitter put up top, if the EP4=100% still less than 10 degree, need to change the pitch range by the step 18,to change the CH6=-50 to -60 or more